All Common Problem Solution For China Phone (read before post)
First we need to know why a phone is dead-
1. For Software
2. For Hardware
1. For Software-
Flash is its final solution, but mtk cpu 90% phone done by format. if its MTK,SPD,AD, SI4904 cpu first try to format than try to full flash your phone with a good and perfect flash file. and other cpu haven't format option, so direct flash them. when you flash careful about original flash file version.
A. what you do before format or flash-
Always remember, before format or flash of your any china phone must first backup your current flash file if phone is dead, also do it. because it will help to find its original flash file version and many other.
B. What you need for flash or format a china phone-
(1) Connecting device (also your can do it with usb to serial cable but a device/box can give you full/final solution)
(2) Phone TX and RX.
(3) Need to know phone cpu type/model, flash chip type/model, Flash file version.
(4) For Flash need a good flash file which same to your phone original flash file version.
C. What problem you face for wrong flash file
(1) phone still dead
(2) white screen
(3) keypad not work
(4) phone hang after power on
(5) keep restarting
(6) no network
[Only registered and activated users can see links. ]
2. For Hardware-
when a dead phone not possible to repair only with software you need to repair phone hardware.
Which hardware you need to check for dead phone-
(1) when you try to flash if phone not boot check power source/battery voltage/V+ pin in phone connector. just do confirm phone found enough voltage for software operation.
(2) if phone power source is ok but still not boot, do confirm your tx and rx is 100% working/tested.
(3) if tx rx is ok, than check your phone connector, its tx rx pin is confirm connect with cable and internal connector pin is joint on pcb perfectly.
(4) if pin is ok, maximum china phone tx rx going to cpu after crossing a resistor or capacitor so check them.
(5) if resistor is ok now you need to check boot diod, all phone have no boot diod so last try is check cpu tx rx pin.
(6) if boot is ok but phone not receive flash file, maximum time this problem coming from flash ic or ram (maximum china phone flash memory and ram have in one chip). so you need to try first re-hot it if still not solve change it.
but its true flash chip/ram always show error not only for them, sometimes cpu to flash chip/ram connection lost for bad cpu pin or bad cpu soldering on pcb. so check both of them.
(7) phone flash ok but not power on (although file is 100% correct) , for it you need to check
Flash chip/ram (95% include in 1 chip)
Clock crystal and battery
26mhz (near rf ic)
Power IC and v+/b+ way
Last try is CPU.
To Be Continue All Problem Solution Step By Step..........................
Re: All Common Problem Solution For China Phone (read before post)
How to repair keypad problem in china phone-
First we need to know china phone keypad connected with PCB how way-
(A) Direct on PCB
(B) Flex System (flex cable direct soldering pcb to keypad panel)
(C) Flex and socket system include (flex one side soldering with key panel other side connect to pcb with socket)
(D) only Socket System (here have 2 socket, 1 with key panel others with pcb)
Keypad problem have various type-
1. All key not work.
2. some key work and some other not work.
3. sometimes work and sometimes not work.
1. All key not work
china phone all key not work for this type of problem-
(A) though its touch screen phone, first try to disconnect touch panel line from phone pcb or display flex (4 line)
(B) though not solve and keypad direct on pcb first you try to good clean full pcb with cleaner.
(C) though not solve now you try to format/flash your phone because some time key problem come from software problem.
(D) though still not solve now you check must be CPU. 95% china phone keypad directly going in cpu. and other 5% first going to resistor or capacitor near the cpu or keypad than going to cpu. so now first check them than you can try to re-hot, re-soldering or changing cpu.
(E) though its flex or socket system, first check GND connection continuslay pcb to key panel. next check full flex or socket all line going continuously pcb to key panel or not. also sometimes flex or socket shorted with other line or gnd so check also them.
(F) Also you can check all key anyone is short 2 line.
(G) sometimes keypad line broken from cpu pin on pcb to key panel, so check them.
2. Some key work and some other not work-
Some key work and some other is not work for this type of problem-
(A) maximum time this problem we face for flex or socket system keypad. so check flex cable and socket all line any line is broken or not and though need change them. and check all key connection on key panel.
(B) though its direact on pcb, some of key line broken internaly. and maximum china phone have alternative test point near every key or with other key on keypad. so check them with multimeter and though need connect to not work key with near testpoint or other working key.
(C) common problem is keypad metal ball (which is short 2 line on key when we press) sometimes its damage for phone water damage or over key voltage, so clean them or change.
(D) also try to check line continuously from cpu to not working key.
3. sometimes work and sometimes not work-
this problem come from this defect-
(A) flex or socket system keypad any line is bad soldering or do lose contact. check them and
re-soldering or keep there line join with extra ware.
(B) for cpu bad soldering or cpu pin is broken. so re-hot or re-ball cpu.
|The Following User Says Thank You to GSM PATTOKI For This Useful Post:|
Join Date: Jan 2017
Posts: 233Status: Offline
Thanked 0 Times in 0 PostsRep Power: 1
Discounts! Wenpod GP1+ 2-axis Handheld Stabilizer for GoPro 3 3+ 4 AI Stabilized Built-in 3.5 inch LCD Monitor
Wenpod GP1+ 2-axis Handheld Stabilizer for GoPro 3 3+ 4 AI Stabilized Built-in 3.5 inch LCD Monitor 171.79$ Wenpod GP1+ 2-axis Handheld Stabilizer for GoPro 3 3+ 4 AI Stabilized Built-in 3.5 inch LCD Monitor... With the launch of GoPro camera, it certainly brings a revolutionary change in videography. WENPOD GP1+ is born for GoPro camera to empower extreme sport lovers shooting stabilized video footage in first-person view, with the help of its built... [Only registered and activated users can see links. ] READ MORE [Only registered and activated users can see links. ] IndoorOutdoor Portable Folding Table Fishing Picnic Roll Up Square Camping Desk Garden Furniture ( 29.60 $) 500ml Thermos Cup Thermos Mug Insulated Tumbler Travel Cups Stainless Steel Vacuum Cup FEN ( 6.52 $) [Only registered and activated users can see links. ] Brazilian virgin hair loose wave 4bundles brazilian loose wave 7a unprocessed brazilian hair weave bundles 100% human hair soft ( 53.34 $) [Only registered and activated users can see links. ] Casual women's strappy crochet backless dress ( 13.53 $) [Only registered and activated users can see links. ] Malaysian virgin hair body wave 4 bundles deal malaysian body wave 7a unprocessed virgin hair weave 100% human hair extensions ( 111.72 $) Mini Waterproof Rechargeable GSM GPS Tracker magnet Long Battery Life Car Human Asset tracking device 30 Days tracking systems ( 40.90 $) Rhinestones Clear Transparent TPU Plating diamond Case For Samsung Galaxy A3 A5 A7 2016 A8 A9 J3 J5 J7 S6 S7 S6 S7 Edge S6 Plus ( 3.99 $) [Only registered and activated users can see links. ] [Only registered and activated users can see links. ] [Only registered and activated users can see links. ] [Only registered and activated users can see links. ]
|Related threads at Dhaka Mobile|
|Thread||Thread Starter||Forum||Replies||Last Post|
|china phone i6310 google code problem||Muvin||Android based mobile phones / Tablets||2||01-26-2014 11:04|
|my phone all headphone solution common||PC Zone||Chinese Models & Cloned Phones||1||07-18-2012 14:32|
|My Phone Headphone Problem Solution||PC Zone||Chinese Models & Cloned Phones||0||07-18-2012 13:38|
|All Common Problem Solution For China Phone (read before post)||::.JALTARANGA.::||Chinese Models & Cloned Phones||4||01-20-2012 16:06|
|common problem difficult to solve try to make it easy||.:Gsmideazone:.||Nokia Hardware & Hardware-Repair Area||66||03-12-2011 08:14|
|Default Style - Mobile Style||
All times are GMT +1. The time now is 10:54.